BMW CAS4 CAN-filter V5 Connection Diagram


BMW CAS4 CAN-filter V5 Connection Diagram


BMW CAS4 CAN-filter is a special module allows to adjust mileage readings in BMW F01, F07, F10 and X3 2011-2012 (with motorola processor 9S12 XEP mask 5M48H / 4M48H – SC 66 7095 CAG).
This is tips of BMW CAS4 CAN-filter V5 Connection Diagram.

BMW filter V5 pinout
 BMW-filter-V5-pinout
CAS connection diagram
 CAS4
F3x IKE
 F3x-IKE
F3x with MOST
 F3x-with-MOST
F15  instrument panel
 
F15 filter wire connection
Brown— can out H
Green— can out L
Yellow— can in H
Blue— can in L
Red— 12V
Black— Ground

NOTE: CANBUS Inductance needs to be removed;
      INS (instrument) chip needs to be dealt with first.

F15 instrument panel filter
 
F18 instrument panel wire connection
 F18_
F35 IKE
 F35_IKE
F56
 F56
FEM connection diagram
 FEM-1
 FEM-2
Note:
bmw-cas4-can-filter-new-a-1
Supported by xingobd2 term
Contacts:
Website: http://www.xingobd2.com
Skype: 8618124509953
Email: admin@xingobd2.com
What;s app: +86 18124509953

评论

发表评论

此博客中的热门博文

How to solve Problem in multiplex network for renault can clip ?

图片
This is how to solve an issue of your  Renault CAN CLIP interface  with an error message “Problem in multiplex network” Almost ALL pcb Renault Can Clip has the bug as a wrong resistors (2 pc) in Low CAN.(Message – “Problem in multiplex network” will be shown) It’s a fairly common problem. The reason to the ugliness is banal – sealed resistors of smaller denomination. Instead of 26.1 kilohms (marking 2612), sealed with 2.61 kOhm (marking 2611). There is a file that point you what resistors must be replaced. Notice it when chose your Clip. It’s in Russian, but a picture explains all. The solution, I think, does not need to be explained. This is the best Renault CAN CLIP pcb with AN2135SC Source:  http://www.xingobd2.com/free-shipping-deals-best-quality-can-clip-v175-for-renault-diagnostic-interface-with-full-chip-an2135sc-an2136sc-multi-languages.html Consists of two boards – CAN and ISO (there are no single-board). On a working device, all four LEDs...
阅读全文

All Benz EIS/EZS Pinouts for Table Connection

图片
Here are all  mercedes-Benz  EIS/EZS pinouts for table connection and test.Just for sharing purpose,credit to DK forum member volism W169 W211 W209 W202 W208 W210 W203 W463 W639 W204 W207 W212 W212 new,W246 W166 EZS W215 W220 W230 W221 new type W211 old type W639 new     W906   W164   NEC  new W164   NEC  old W166 W246 VVDI 246 one plug Related item: VVDI Prog Benz EZS/EIS adapters CGDI Pro MB VVDI MB BGA Tool For further info.please use our online service www.xingobd2.com or  skype  if you have . website: www.xingobd2.com skype : +8618124509953 whatsApp:+8613728952674
阅读全文

Carprog 9.31 reads/writes eeprom 95160 with A4/A6 adapter

图片
Errors and solutions here for eeprom 95160 read/write with  Carprog 9.31 programmer : Error 1:  “ID not found” when read eeprom 95160 Error 2 : “Verify error” when read eeprom 95160 Error 3 : “Verify OK” when read eeprom; “Verify error” when write it Case: Carprog reads/writes eeprom 95160 from bsi citroen berlingo 2004 In detail… Error 1 : “ID not found” when read eeprom 95160 I connect usb cable with  carprog  and a6 clip to eeprom 95160 . it gives me error “ID not found” . Solution 1 : Desoldering the eeprom from circuit board and read not in circuit board, read eeprom on the table Error 2 : “Verify error” when read eeprom 95160 Read with A6 clip. There is an error Solution 2 : Take a look here Error 3 : “Verify OK” when read eeprom; “Verify error” when write it if i read it, verify ok If write it, verify error Solution 3 : probably have a damaged carprog. Replace 74hc1...
阅读全文