Digiprog 3 clone Test on VW Golf 6 Odometer Correction

xingobd2 engineer share a Digiprog 3 clone test case on VW Golf 6 2012 Mileage programming.

Here you go…. Digiprog 3 clone changes km of Golf 6 2012
the current mileage: 212099km
digiprog-3-golf-6-odometer-correction-1digiprog-3-golf-6-odometer-correction-2 connect Digiprog 3 to the car via OBD
then the machine starts
select a car: VW-Golf-Golf 6-Tacho Diag 2012
digiprog-3-golf-6-odometer-correction-3digiprog-3-golf-6-odometer-correction-4digiprog-3-golf-6-odometer-correction-5digiprog-3-golf-6-odometer-correction-6digiprog-3-golf-6-odometer-correction-7
DP3 is reading the current mileage
digiprog-3-golf-6-odometer-correction-8digiprog-3-golf-6-odometer-correction-9digiprog-3-golf-6-odometer-correction-10
Golf 6 mileage is read out
it’s 212128km, almost the same as what displayed on the dashboard
digiprog-3-golf-6-odometer-correction-11
enter a new mileage to change
new mileage: 200000km
digiprog-3-golf-6-odometer-correction-12digiprog-3-golf-6-odometer-correction-13
the mileage on the dash is also changed!
digiprog-3-golf-6-odometer-correction-13
Digiprog 3 china clone is confirmed to OBD change km for Golf6!
Works perfect!
Get best price,plz contact with :
E-mail: admin@xingobd2.com
Hot line: +8613728952674
Whats app:+8613728952674
Skype: 8618124509953

评论

发表评论

此博客中的热门博文

How to solve Problem in multiplex network for renault can clip ?

图片
This is how to solve an issue of your  Renault CAN CLIP interface  with an error message “Problem in multiplex network” Almost ALL pcb Renault Can Clip has the bug as a wrong resistors (2 pc) in Low CAN.(Message – “Problem in multiplex network” will be shown) It’s a fairly common problem. The reason to the ugliness is banal – sealed resistors of smaller denomination. Instead of 26.1 kilohms (marking 2612), sealed with 2.61 kOhm (marking 2611). There is a file that point you what resistors must be replaced. Notice it when chose your Clip. It’s in Russian, but a picture explains all. The solution, I think, does not need to be explained. This is the best Renault CAN CLIP pcb with AN2135SC Source:  http://www.xingobd2.com/free-shipping-deals-best-quality-can-clip-v175-for-renault-diagnostic-interface-with-full-chip-an2135sc-an2136sc-multi-languages.html Consists of two boards – CAN and ISO (there are no single-board). On a working device, all four LEDs...
阅读全文

All Benz EIS/EZS Pinouts for Table Connection

图片
Here are all  mercedes-Benz  EIS/EZS pinouts for table connection and test.Just for sharing purpose,credit to DK forum member volism W169 W211 W209 W202 W208 W210 W203 W463 W639 W204 W207 W212 W212 new,W246 W166 EZS W215 W220 W230 W221 new type W211 old type W639 new     W906   W164   NEC  new W164   NEC  old W166 W246 VVDI 246 one plug Related item: VVDI Prog Benz EZS/EIS adapters CGDI Pro MB VVDI MB BGA Tool For further info.please use our online service www.xingobd2.com or  skype  if you have . website: www.xingobd2.com skype : +8618124509953 whatsApp:+8613728952674
阅读全文

Carprog 9.31 reads/writes eeprom 95160 with A4/A6 adapter

图片
Errors and solutions here for eeprom 95160 read/write with  Carprog 9.31 programmer : Error 1:  “ID not found” when read eeprom 95160 Error 2 : “Verify error” when read eeprom 95160 Error 3 : “Verify OK” when read eeprom; “Verify error” when write it Case: Carprog reads/writes eeprom 95160 from bsi citroen berlingo 2004 In detail… Error 1 : “ID not found” when read eeprom 95160 I connect usb cable with  carprog  and a6 clip to eeprom 95160 . it gives me error “ID not found” . Solution 1 : Desoldering the eeprom from circuit board and read not in circuit board, read eeprom on the table Error 2 : “Verify error” when read eeprom 95160 Read with A6 clip. There is an error Solution 2 : Take a look here Error 3 : “Verify OK” when read eeprom; “Verify error” when write it if i read it, verify ok If write it, verify error Solution 3 : probably have a damaged carprog. Replace 74hc1...
阅读全文